TRANSMISSION GASKETS & SEALS for Beetle Ragtop 1959

This transmission gasket set has everything you will need to overhaul your swing axle or type 1 transmission.
Beetle Type 1: 61-79
Bus Type 2: 61-67
Ghia: 61-74

Kit includes all the gaskets and O-rings required to assemble a Type 2 Bus 002 style standard transmission. These gasket sets are manufactured by an O.E. supplier. Each gasket is cut from material of the same type and thickness as original. Note- the drive flange and cup seals are not included. FITS: Bus 1968 to 1975
Bus Tyle 2: 68-75
Transmission Type: Bus 002

Replacement mainshaft seal on both irs and swing axle VW transmissions. Insures against gear oil leaking into the bellhousing and wrecking your clutch
Ghia: 56-74

PREMIUM VERSION
Replacement mainshaft seal on both irs and swing axle VW transmissions. Insures against gear oil leaking into the bellhousing and wrecking your clutch
Ghia: 56-74

These are the seals that tap into the drive flanges on type 1 vw IRS transmissions. Behind these seals is the snap ring to hold the drive flange to the output shaft on the transmission. Over time these can become dislodged or begin leaving. They are pressed in and should be replaced whenever you have a CV joint off
Type 3: 69-74

Axle tube gaskets are used on vw swing axle transmissions between the case and the 6 bolt flange that holds the axle tube on. These are also considered shims to help adjust the axle tube. You will need to start with 6 shims and remove 1 at a time until the axle has a steady but controlled drop.

These special urethane seals fit right into the cv joint flanges to prevent the axles from beating the transmissions. Tough urethane will not tear or flatten like stock seals. For use with T1 to T2 conversion drive flanges and T1 stock drive flanges. Sold in pairs

Final drive seals for irs transmissions. These seal around the drive flangles on the side of a irs transmission.
36mm ID x 60mm OD x 15mm Thick
Beetle Type 1: 69-79
ghia: 69-74

These special urethane seals fit right into the CV joint flanges to prevent the axles from beating the transmissions. Tough urethane will not tear or flatten like stock seals. Sold in pairs

REPLACEMENT SIDE COVER SEAL FOR inches 002 inches TYPE 2 BUS TRANSMISSION. CHECK YOUR SEAL MEASUReMENTS, SOME EARLY 3 RIB TRANSMISSIONS USE A DIFFERENT SEAL NOT AVAILABLE TO US.
42MM X 67MM X 17 6MM
Bus Type 2: Late 68-75
Transmission Type: Type 2 002

Replacement seal for the final drive on all inches 091 inches 6 rib transmission. This is the seal that goes into the side cover and seals around the splined stub that comes out from the ring and pinion. It is behind the CV Flange.
Dimensions:
45mm x 72mm x 15mm
Transmission: 091 VW Bus
Bus Type 2: 76-79

Replacement nose cone seal. Presses into the brass housing at the end of your nose cone on type 1 applications
Beetle: All years
Transmission Type: All Type 1

Type 2 replacement drive flange plug, fits 69-79
Bus Type 2: 68-79
Vanagon: 80-92
Transmission Type: Bus 002.

These strong metal main bearing thrust plates eliminate movement of main shaft bearings. Aids in maintaining the alignment of the gears on the pain and pinion shafts to give the gears FULL contact thereby reducing the changes of failure
Transmission Type: Type 1 All
Material: Steel

This hardened steel shift ball replaces the factory plastic unit which when subjected to any abuse will usually fail. Precision built to slip right in to your Type 2 IRS.

These strong metal main bearing thrust plates eliminate movement of main shaft bearings. Aids in maintaining the alignment of the gears on the pain and pinion shafts to give the gears FULL contact thereby reducing the changes of failure
Transmission Type: Type 2 All
Material: Steel

Replacement mainshaft Bearing for Type 1 and Type 2 Transmissions
Bus Type 2: 71-75

Replacement mainshaft Bearing for Type 1 and Type 2 Transmissions
Beetle Type 1: 74-75
Bus Type 2: 71-75