FUEL PUMPS for Beetle Sedan 1959

Replacement mechanical fuel pump. Generator style. Utilizes the longer push rod 4-1/4 inches . PUMP MAY NOT LOOK AS PICTURED, THE POSITION OF THE INLET AND OUTLET MAY BE DIFFERENT
Beetle Type 1: 61-73
Push Rod Length: 4.25 inches
Style: Generator

PREMIUM VERSION
bocar brand
Replacement mechanical fuel pump. Generator style. Utilizes the longer push rod 4-1/4 inches . PUMP MAY NOT LOOK AS PICTURED, THE POSITION OF THE INLET AND OUTLET MAY BE DIFFERENT
Style: Generator

Stock replacement mechanical fuel pump. Generator style. This is chrome polished for a nice clean look. Please bare in mind, this is a inexpensive item with a lot of different shapes to it. Please don't expect a mirror finish on the chrome. .
Fuel line outlet pipes may be different then whats pictured because of different manufactures.
Its a good ideal to prime a new pump before attempting to pump fuel. You may need to make sure your tank is higher then the pump to get a good fuel flow.
113-127-025B
Beetle Type 1: 66-76
Bus Type 2: 66-71
Fits vw engines with Generator

PREMIUM VERSION
Brosol BRAND
Mechanical fuel pump. Late model with alternator. Gaskets included. Alternators came factory after 73 but it is very common to have one on that is aftermarket. If your not sure if you have a alternator or generator just look at the shape of it. If it is one diameter all the way from the front to back then it is a generator. If it is bigger in the front by the pulley and smaller where it attaches to the fan then it is a alternator
Style: Alternator

Replacement fuel pump push rod for alternator style pumps. Be aware of a difference in length for both alternator style and generator style or damage may occur. 4 inches
Ghia: 71-74

Replacement fuel pump push rod for generator style pumps. Be aware of a difference in length for both alternator style and generator style or damage may occur. This is 4-1/4 inches long
Ghia: 61-73

Replacement fuel pump to flange gasket. This gasket is located directly below the fuel pump flange block. This should be replaced anytime you replace the fuel pump. Sold Each
Ghia: 61-74

Gasket between fuel pump and fuel pump flange block. This one goes on just before the fuel pump and has a small hole for the pushrod tube. This should be replaced anytime the fuel pump comes off
Ghia: 61-74

Replacement fuel pump flange block. This flange block guides the fuel pump push rod during normal operation. Should be replaced when changing pumps
Ghia: 61-74

Solid State 12 volt reliability pumping 30 G.P.H @ 3-4.5 PSI. Use with gasoline or alcohol. Requires the use of 1/8 NPT hose barbs or adapters, depending on you fuel line choice. NOTE: IT IS HIGLY RECOMMENDED THAT A FUEL PRESSURE REGULATOR BE USED. Weighing slightly over a pound. 2 hose barbs for 1/4 fuel line and clamps included. NOTE: Color and Brand May Vary. Overall width: 2 7/8 inches Width (housing): 1 9/16 inches Mount pattern: 2 5/8 inches center-to-center Height: 2 3/8 inches Length: 1 7/8 inches Thread: 1/8 inches NPT

This 12v inline fuel pump provides a quiet 30 gph fuel flow at 2-4 psi and requires no pressure regulator. 5/16 inch inlet and outlet. Fuel filter and mounting hardware included. Measures 10 inches long

Solid state for reliability and made with heavy duty case. We recommend the use of a fuel regulator. Fittings and Clamps NOT included

Flows 110 gph. Awsome racing pump

New lower housing casting for enhanced fuel flow Improved design for street/strip applications. Distinctive ?BLACK? logo.
Compatible with alcohol or methanol fuels
Flows 140 GPH (free flow) Flows 120 GPH at 9 PSI. Maximum pressure is 14 PSI
3/8? NPT inlet and outlet ports Fuel pressure regulator is required (Recommend Holley P/N 12-704 for gasoline & P/N 12-707 for alcohol) Motor draws only 4 Amps current 7 1/2 Amp fuse recommended. Provides constant fuel flow with no pulsation. Has externally accessible pressure relief valve (max 14 PSI) Rotor/Vane pump design is more tolerant of contaminated fuels. Weighs only 3 lbs, Includes mounting bracket.
Repair kits are readily available
Can be serviced from either pump end or brush cap end . Use of safety shut-off switch, P/N 12-810, strongly recommended . Not designed or recommended for use with fuel injection systems

Features
tumble polished billet look
new lower housing casting for enhanced fuel flow and quieter operation
maximum pressure is 7 psi
motor draws 2 amps current
7 1/2 amp fuse recommended
constant fuel flow with no pulsation
improved design for street/strip applications
distinctive ?red? logo
flows 97 gph (free flow)
flows 71 gph at 4 psi
regulator is not required
has externally accessible pressure relief valve (max 7 psi)
rotor/vane pump design is more tolerant of contaminated fuels
weighs only 2.88 lbs
includes mounting bracket
repair kits are readily available
can be serviced from either pump end or brush cap end
not compatible with alcohol or methanol fuels
use of safety shut-off switch, p/n 12-810, strongly recommended
not designed or recommended for use with fuel injection systems

This is the answer to mounting problems of our electric fuel pumps.
This allows the pump to be mounted directly over were a stock mechanical pump used to be. This usually allows you to reuse your old fuel lines since they should be in roughly the same area.
Comes complete with gaskets and mounting hardware
Quantity: Sold Each

Great looking addition to any engine running an electric pump. Both functional and sharp this cover is fully machined from billet aluminum.
Black Anodized
Comes complete with mounting bolts and gasket
Quantity: Sold Each.

Billet fuel pump block off with built in coil mount. Hard anodized. Includes npt fitting for oil return or breathing. Black in color
Quantity: Sold Each

Billet fuel pump block off with built in coil mount. Hard anodized. Block off is threaded to add fitting for oil return or breathing. Red in color. Will not work with single carbs
Quantity: Sold Each

Great looking addition to any engine running an electric pump. Both functional and sharp this cover is fully machined from billet aluminum.
Blue Anodized
Quantity: Sold Each.

Great looking addition to any engine running an electric pump. Both functional and sharp this cover is fully machined from billet aluminum.
Red Anodized
Quantity: Sold Each.

This 12v inline fuel pump provides a quiet 5 to 5.5 pounds of pressure.
5/16 inlets and outlet with built in filter.
Note: It is always a good idea to run a fuel pressure regulator with electric pumps

Billet fuel pump block off with built in coil mount. Hard anodized. Includes npt fitting for oil return or breathing. Blue in color
Quantity: Sold Each

Billet fuel pump block off with 3/8 npt vent hole for easy breather setup. Anodized black. Includes hardware
Quantity: Sold Each

Billet fuel pump block off with 3/8 npt vent hole for easy breather setup. Anodized blue. Includes hardware
Quantity: Sold Each

Billet fuel pump block off with 3/8 npt vent hole for easy breather setup. Anodized red. Includes hardware
Quantity: Sold Each

Billet fuel pump block off with built in coil mount. Hard anodized. Block off is threaded for oil return or breathing. Chrome in color. Will not work with single carbs
Color: Polished
Quantity: Sold Each

Great looking addition to any engine running an electric pump. Both functional and sharp this cover is fully machined from billet aluminum.
Quantity: Sold Each

Fuel Pump Bracket - 2 Piece - Clamp-On - 1-1/2 in OD Tubes - 1-1/8 in Diameter - Aluminum - Black Anodized - Each

High flow, low pressure electric fuel pump equipped with a 5/16 In inlet/outlet. The pump flows 18 gph at 4.0 psi, 5.5 psi maximum. Includes a rubber padded mounting bracket and two heavy duty hose clamps. Rated 12 volt/5 amp. Overall length is 5-1/2 In x 1-1/2 In wide.

This cast aluminum fuel pump block off features a 12mm threaded breather boss for extra venting.
Comes complete with the gasket.
A must for eliminating your stock mechanical fuel pump and installing a electric system
Quantity: Sold Each

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

Billet aluminum, CNC machined, and anodized for that finishing touch. They come in Red, Blue & Black with JAYCEE engraved on top. The mounting hardware is included.

JayCee's Billet one piece block off is the first of its kind. Manufactured with a dash 8 fitting and a tapered hole for max breathing.

JayCee's Billet one piece block off is the first of its kind. Manufactured with a dash 8 fitting and a tapered hole for max breathing.

JayCee's Billet one piece block off is the first of its kind. Manufactured with a dash 8 fitting and a tapered hole for max breathing.

JayCees Billet one piece block off is the first of its kind. Manufactured with a dash 10 fitting and a tapered hole for max breathing.

JayCees Billet one piece block off is the first of its kind. Manufactured with a dash 10 fitting and a tapered hole for max breathing.

JayCees Billet one piece block off is the first of its kind. Manufactured with a dash 10 fitting and a tapered hole for max breathing.