GASKETS & SEALS for Beetle Sedan 1968

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
EMPI's Dual Port Intake Manifold Gaskets are made to fit the Type 1 based dual port intake manifolds.
Quantity: 2 Pieces

Will fit any dual port type 1 engine. Has an additional hole for the mounting bolt for certain intakes.
The pair of gaskets fit 1971 through 1974 Beetles, Super Beetles and Karmann Ghias, 1971 Type 2 Bus models and 1973 through 1974 Things. The thick paper gaskets ensure a leak free seal between the intake manifolds and the heads.
Dual Port

Base gasket for Solex 28 and 30 PICT carbs.
Type 1 50-70
Ghia 56-70
Type 2 50-70
Ghia: 56-70
Quantity: Sold Each

Carburator base gasket to go between carburator and intake, fits 34 ict carburator, sold in pairs
Carburetor: 34 ICT

Intake Manifold Gasket, 1300-1600cc Single Port
should be replaced EACH time the intake is removed from the cylinder head. These compress and deform, and will not seal if you try to re-use them
This also fits single port Type 3s

WEBER IDF and DELLORTO DRLA base gaskets. Hi quality gasket material helps prevent leaks between the carbs and the intakes. Sold in pairs
Carburetor: IDF & DRLA 40 & 44
Location: Carb to Intake
Quantity: 2 Pieces

Carburator base gasket to go between carburator & intake, fits holley/weber dfv carburator with isolated manifold.
sold as a pair.
Carburetor: Holley/Weber DFV
Quantity: 2 Pieces

Replacement kadron base gaskets rings. Seal your air filters on tight with these cork covers. Do not let sand and dirt ruin your motor because of a bad seal
Carburetor: Kadron
Quantity: 2 Pieces

Base gaskets for between the carb and intake for a 34 carb. Sold Each
113-129-707A
Carburetor: Solex 34 PICT 3
Quantity: 1 Pieces

Carburator base gasket to go between carburator & intake fits weber 40/42 dcnf carburator, sold in pairs
Carburetor: Weber DCNF 40 42

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
Carburetor: 32/36 Progressive
Quantity: 2 Pieces

Replacement carb gasket for empi, solex, brosol 40 ies. Sold as a pair. Fits between the intake and the carb
Carburetor: Brosol 40
Carburetor: Solex 40
Carburetor: EMPI 40 EIS

These innovative isolator mounts fit between the intake manifold and carb to dampen fuel vibrations in EMPI and Weber float bowls. by absorbing the shock you will reduce fuel foaming, cut down on erratic needle and seat motion, stabilize the fuel curve
Carburetion: 44mm IDF & HPMX
Quantity: Pair

These innovative isolator mounts fit between the intake manifold and carb to dampen fuel vibrations in EMPI and Weber float bowls. by absorbing the shock you will reduce fuel foaming, cut down on erratic needle and seat motion, stabilize the fuel curve
Carburetion: 40mm IDF & HPMX
Material: Polyurethane
Quantity: Pair

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
EMPI's Bugspray or NDIX Carburetor Base Gaskets are sold as a pair and fit the Holley Bugspray or Zenith NDIX series carbs. The thick paper gaskets ensure a leak free seal between the carburetor and the intake manifold.

These innovative isolator mounts fit between the intake manifold and carb to dampen fuel vibrations in EMPI and Weber float bowls. by absorbing the shock you will reduce fuel foaming, cut down on erratic needle and seat motion, stabilize the fuel curve
Carburetion: 48 IDF & EPC
Quantity: Pair

These innovative isolator mounts fit between the intake manifold and carb to dampen fuel vibrations in EMPI and Weber float bowls. by absorbing the shock you will reduce fuel foaming, cut down on erratic needle and seat motion, stabilize the fuel curve
Carburetion: 51 IDF & EPC
Quantity: Pair

If your checking your floats or replacing your needle and seat you will need these high quality top plate gaskets. Sold as a pair
Carburetor: Weber IDF 40 44
Carburetor: EMPI HPMX 40 44

JayCee's New Vibration Isolators are made for the performance enthusiast. Our billet aluminum retainer encapsulates two urethane gaskets. The purpose is to manage fuel pressure control from vibration along with heat rise to your fuel bowls.

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
Location: Air Cleaner to Carb
Quantity: 2 Pieces..

Replacement top gasket Fits both 48 and 51 EPC and Weber IDA Carbs
Quantity: Sold Each.

Air filter base gasket to go between filter and carburator body for weber dcnf carburator, sold in pairs
Carburetor: Weber DCNF
Quantity: 2 Pieces

Air filter base gasket, to go between filter and carburator body, fits weber dcoe carburator, sold in pairs
Carburetor: Weber DCOE
Quantity: 2 Pieces

Air filter base gasket to go between filter and carburator body, fits weber dgv carburator, sold in pairs
Carburetor: Weber 32/36 DGV
Carburetor: 38 EPC
Quantity: 2 Pieces

Air filter base gasket for weber 48 ida carburator, includes velocity stack spacers, sold in pairs
Carburetor: Weber 48 IDA
Quantity: 2 Pieces

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
EMPI's Dual Port Intake Manifold Gaskets are made to fit L5 Intake manifolds
Head Type: Dual Port
Material: Gasket Board
Quantity: 2 Pieces

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
EMPI's Dual Port Intake Manifold Gaskets are made to fit L7 Intake manifolds
Quantity: 2 Pieces

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
EMPI's Dual Port Intake Manifold Gaskets are made to fit D7000 Intake manifolds
Quantity: 2 Pieces

Precision die cut from the best available gasket material for perfect seal and fit. Easily adapted to even modified applications
EMPI's Dual Port Intake Manifold Gaskets are made to fit L6 Intake manifolds
Quantity: 2 Pieces

If your checking your floats or replacing your needle and seat you will need these high quality top plate gaskets. Sold as a pair
Carburetor: 38 EGAS (DGV)

If your checking your floats or replacing your needle and seat you will need these high quality top plate gaskets. Sold as a pair
Carburetor: 32/36 DFV.