TRANSMISSION TOOLS for Beetle Sedan 1971

EMPI's VW Transaxle Drain Plug is a 17mm Allen Head and fits a 3/8 Inch Drive Ratchet. The Allen drive socket can be used to remove or install the transmission drain or fill plugs and also fits the IRS Suspension Pivot Bolt.

Use this tool to drain the oil from the transaxle.
17mm. Will work for the IRS pivot bolts also

EMPI s VW 12 Point CV Bolt Socket fits the 6mm, 12 point drive for the CV Joint Bolts. The socket fits 3/8 drive ratchets. The 12 point CV Joint Tool is a must for removing old grease and dirt packed CV joint bolts. Don t try to use a 6mm Allen head with 12 point bolts as they are easily stripped!

High quality 6 point socket hex tool for removing cap screws holding the constant velocity joints on suspension

Made from billet aluminum, this hub cap puller is also a jack hole cover. Two spring steel wire fingers hook into the drain holes in the edge of the hub cap and removes them without damaging them. Stores in the jack ports while not in use

Made from billet aluminum, this hub cap puller is also a jack hole cover. Two spring steel wire fingers hook into the drain holes in the edge of the hub cap and removes them without damaging them. Stores in the jack ports while not in use. Has empi engraged into it

Empi offers a reproduction of the o.E. Hubcap puller. Polished stainless cover on a plastic body and plated wires just like to original

This tool has been designing to simplify the task of adjusting clutch cables on air cooled VWs having wing nuts. The tool has four gripping areas- rather than the wing nuts two- which provides for greater ease in turning the nut. The hand force required to turn the wing nut is reduced since greater leverage can be applied through the use of this tool.

This alignment tool is a must when changing clutch discs on your type 1 engine. Insures the transmission input shaft will have an easy transition through the clutch disc
Material: Impact Plastic
Type 1 Beetle
Type 1 Ghia
Thing
Type 2 Bus 50-71
Type 3 62-73
Vanagon Diesel 82-84
VW Dasher 75-81
Fox 87-93

Tips reach to grease fittings in tight areas, such as U-joints, and may also be used to grease the ball spline unit on Bert transmissions. The 2 In tip replaces the standard end on most guns with 1/8 In NPT. Quick release 4 In tip includes a small and large sleeve to fit standard couplers. Tips are for hand operated grease guns only.

This alignment tool is a must when changing clutch discs on your type 1 engine. Insures the transmission input shaft will have an easy transition through the clutch disc
Fits the following
New Beetles 98-99
All 16 Valve VW
Material: Impact Plastic.

Contain the mess of bleeding brakes by capturing fluid in this 16oz. bottle with a 12 In long hose which attaches to most bleeder screws. The removable cap has a built-in fitting to secure the hose during storage to help prevent spills. Choose from a steel lanyard retainer that suspends the bottle from a chassis or suspension component or a magnet retainer to secure the bottle to a steel object such as a brake drum or rotor during bleeding. ALL11017 has a magnet retainer and a one way check valve built-in for one person brake bleeding.

This alignment tool is a must when changing clutch discs on your type 1 engine. Insures the transmission input shaft will have an easy transition through the clutch disc
Engine Type: Type 1, Ghia Autosticks
Material: Impact Plastic.

Contain the mess of bleeding brakes by capturing fluid in this 16oz. bottle with a 12 In long hose which attaches to most bleeder screws. The removable cap has a built-in fitting to secure the hose during storage to help prevent spills. Choose from a steel lanyard retainer that suspends the bottle from a chassis or suspension component or a magnet retainer to secure the bottle to a steel object such as a brake drum or rotor during bleeding. ALL11017 has a magnet retainer and a one way check valve built-in for one person brake bleeding.

This alignment tool is a must when changing clutch discs on your type 1 engine. Insures the transmission input shaft will have an easy transition through the clutch disc
VW Carrado 89-95
Passat 89-95
Material: Impact Plastic.

Quality gun has comfort grip handle for easy, one hand operation. Gun accepts a standard 14 oz. grease cartridge, features an air bleeder valve to eliminate air lock, and includes a flexible 12 In long fill hose.

Brake pressure gauge kit includes two gauges allowing one gauge to be used in the front and one in the rear brake system. Compare front to rear pressures to help diagnose problems or to preset your brake bias. Gauges easily replace 1/4 In-28 brake bleeders which are commonly found in most aftermarket calipers.

Gauge temporarily replaces the bleeder screw in most aftermarket brake calipers with 1/4 In-28 thread bleeder screws to measure brake pressure. Swivel head positions the 2-3/4 In diameter gauge for easy viewing. Convenient remote bleeder can be used to evacuate air in the system for accurate readings.

Cut plastic, aluminum, copper or steel tubing without distorting or crushing. Standard cutter works with tubing from 1/8 In up to 1-1/8 In and has wide rollers for even tracking of cutter wheel, built in reamer for cleaning inside of tubing and an extra cutting wheel. Mini cutter can cut tubing from 1/8 In to 5/8 In in tight areas.

Cut plastic, aluminum, copper or steel tubing without distorting or crushing. Standard cutter works with tubing from 1/8 In up to 1-1/8 In and has wide rollers for even tracking of cutter wheel, built in reamer for cleaning inside of tubing and an extra cutting wheel. Mini cutter can cut tubing from 1/8 In to 5/8 In in tight areas.

Tips reach to grease fittings in tight areas, such as U-joints, and may also be used to grease the ball spline unit on Bert transmissions. The 2 In tip replaces the standard end on most guns with 1/8 In NPT. Quick release 4 In tip includes a small and large sleeve to fit standard couplers. Tips are for hand operated grease guns only.

Contain the mess of bleeding brakes by capturing fluid in this 16oz. bottle with a 12 In long hose which attaches to most bleeder screws. The removable cap has a built-in fitting to secure the hose during storage to help prevent spills. Choose from a steel lanyard retainer that suspends the bottle from a chassis or suspension component or a magnet retainer to secure the bottle to a steel object such as a brake drum or rotor during bleeding. ALL11017 has a magnet retainer and a one way check valve built-in for one person brake bleeding.

Double flares 3/16 In, 1/4 In, 5/16 In, 3/8 In and 1/2 In steel or aluminum and.040 In copper tubing at 45 degrees, the most common flare used in custom brake and fuel lines. Includes detailed instructions and a convenient plastic storage case.

Gauge temporarily replaces the bleeder screw in most aftermarket brake calipers with 1/4 In-28 thread bleeder screws to measure brake pressure. Swivel head positions the 2-3/4 In diameter gauge for easy viewing. Convenient remote bleeder can be used to evacuate air in the system for accurate readings.