TRANSMISSION MOUNTS STEEL for Super Beetle Convertible 1976

Items: 114 of 14
    • 8% less
    Designed to eliminate broken mounts this kit also prevents twisting and spreading of the vw mount horns. This kit consists of front and rear formed steel retaining straps solid steel motor frames steel nose mount and all the heavy duty hardware
    • $73.99
    • 8% less
    It is common knowledge that the bus irs transmission is a superior unit. This kit adapts this transmission to a standard irs setup. Does not include axles
    • $96.99
    • 8% less
    Allows use of stock motor mounts while at the same time bracing and strengthening the frame horns. Special rubber extrusion fits over straps to isolate noise
    • $62.99
    • 8% less
    Stabilizes the frame horns it provides a solid mount for the transaxle. Provisions are also made for chassis support straps. Hardware included
    • $38.99
    • 8% less
    Allows use of stock motor mounts while at the same time bracing and strengthening the frame horns. Special rubber extrusion fits over straps to isolate noise
    • $28.99
    • 8% less
    Kits are designed to add the safety feature of solid mounts by replacing the stock rubber mounts and eliminating damaged or broken mounts. Kit includes all hardware. Front mount only
    • $12.99
    • 8% less
    Now you can cure nosecone breakage by adapting the three hole nosecone to 1961-1967 chassis. Great for baja bugs drag cars and especially sand rails. Nosecone not included
    • $13.99
    • 8% less
    This transaxle adapter kit made by EMPI is used to install a full-syncro (1961 and later) transaxles in 1960 and earlier Type 1 VWs, which have different mounting points. This kit can be easily installed onto the chassis using two M10-1.5 bolts with washers. This adapter only fits 1960 and earlier Standard Beetles and Karmann Ghias.
    • $19.99
    • 8% less
    Unique adapter allows the installation of all vw engines in 68-71 vws when rear mounting is required. Uses oil pump installation studs and lower case through bolt. This neat mount can also be used as a reinforcement for skid plates
    This VW Engine Case Adapter with 8mm thread Pump Cover allows you to install a Type 1 case onto a Type 2 or 3 without the stock 3 point mount.
    • $18.99
    • 8% less
    Weld in center transmission mounts. Add additional support to your 002 or 091 vw bus transmission. Welding required
    • $22.99
    • 8% less
    Replace your worn or stripped trans mount bolts with new. For all swing axle trans mounts including stock cradle, securing the stock-style trans cradle or performance trans mounts to yoke
    113-301-257
    • $6.99
    • 8% less
    Replace your worn or stripped trans mount bolts with new. For all swing axle trans mounts including stock cradle, securing the stock-style trans cradle or performance trans mounts to yoke
    • $2.99
    • 8% less
    This heavy duty rear gearbox cradle fits the following
    Will accept stock rubber mounts
    Ghia: 56-72
    Bus Type 2: 50-67
    Thing: 73-74.
    • $34.99
    • 8% less
    Do You Run Your Car in Class 11 or Terrorize Your Local Dragstrip? Maybe You Just Want Piece of Mind When Power Shifting Your Hot Rod VW. Whatever the Case May Be, EMPIs Weld-In Transaxle Mid Mount Delivers.
    Designed Using 3D CAD and Manufactured Using 5mm Thick AISI 1018 Cold Drawn Steel, This Mount Ensures That the Transmission Stays Where it Belongs and Broken Nose Cones are a Thing of the Past.
    Fits All Type 1 Beetles Using a Stock Transaxle Case.
    Mounting Requires Modification to the Chassis and Must Be Welded Into Place.
    Only 0 left in stock
    • $22.99