TRANSMISSION MOUNTS STOCK for Type 3 Notchback 1971

Front transmission mount for your Aircooled VW Beetle. This is a OEM style replacement
Application year: 66,67,68,69,70,71,72

Replacement front transmission mount for VW. These often crack and can result in excessive engine movement and clutch chatter. This will go between the front of the transmission and the torsion housing where the shifter connects. Check out your mount on the torsion before ordering. Make sure it is a 3 bolt mount and not a 2 bolt
Quantity: Sold Each

Replaces your worn out or broken motor mount and eliminates engine vibration. Oem replacement. This will fit left or right sides. These get bolted onto the bellhousing before the motor is attached. These need to be used with transmission mounting plates that are radiused. If you have a solid mount plate which are flat, installed in your offroad car, these will not bolt into place. Also be sure you use the stock front mount with these not a solid mount
Thing: 73-74

These are heavy duty rear transmission mounts for all years VW Type 1 transmissions. Replace your beat up or broken mounts with these quality heavy duty units
Beetle Type 1: 45-79
Quantity: Sold Each

This is the left side rear transmission mount for air cooled VW. These bolt to the transmission and then into the torsion horn and are side dependant. These often crack and can result in excessive engine movement and clutch chatter
Ghia: 73-74
Side: Left

This is the right side rear transmission mount for air cooled VW. These bolt to the transmission and then into the torsion horn and are side dependant. These often crack and can result in excessive engine movement and clutch chatter
Ghia: 73-79
Side: Right

Engine Mount For 68-71 Type 2 Bus. Sold Each
Bus Type 2: 68-71.

The mounts are for the cross member on 1972-1979 Type 2 Bus Engines. Sold Each
Bus Type 2: 72-79

Front replacement transmission mount for you VW Bus Type 2
Bus Type 2: 63-67.

Transmission Mount For 1972-1979 Type 2 Bus. Sold Each
Bus Type 2: 72-79.

Front transmission mount for your aircooled VW beetle. This is a OEM style replacement.
Application year: 61,62,63,64,65

This Urethane Transmission Mount Kit is 3 pieces and includes hardware. The kit is made from injection molded red urethane. These mounts greatly minimize flexing without the noise of steel mounts. This kit will fit the 1961-1972 Type 1.

Easily update to the stronger late model 3 bolt nose cone. A non-solid inches bolt-in inches conversion mount for late model 3 bolt nose cones into early style vw type 1 chassis. Constructed of durable urethane and complete with all hardware

Made of tough urethane these mounts feature steel sleeves and grade 5 hardware. Front mount only 61-72

Weld in front mount brackets for late model bus transmissions. Rear bolt mounts and hardware included. Take the stress off your nose cone by welding in this mount kit. Saddles up to chassis for easy centering

Firmly encompasses trans and frame horns to reduce vibration and prevent flex and breakage. Rubber insulation reduces noise. Can be used with stock or urethane mounts. Complete kit

Firmly encompasses trans and frame horns to reduce vibration and prevent flex and breakage. Rubber insulation reduces noise. Can be used with stock or urethane mounts. Rear section only

This front transaxle support strap from EMPI secures the trans to reduce vibration and flexing that can lead to unnecessary wear. The support strap is made of zinc plated steel for strength and weather resistance. The rubber insulation on the straps helps to minimize noise by isolating vibration. This front support can be used in conjunction with both stock and urethane mounts. It fits all VW Beetle models through 1979.
FRONT MOUNT ONLY

These 10mm x 100mm studs solve the problem when adapting type 2 transmissions to a new engine. Extra length allows for use of engine mount plates.
Thread: 10mm
Quantity: Sold as a Pair

Maximum support with minimal noise. This kit features heavy channel style rubber insulation. Wraps around stock mount saddle. Can use stock or urethane mounts

Super Transmission Mount, Bolts Securely To Trans And Butts Up Firmly To Frame Horns

Fabrication mount for a mendeola 2d transmission. Front mount.
Hole Spacing
Upper Inner Holes: 6-3/4 inches
Lower Inner Holes: 4-3/4 inches
Outer Holes: 11-1/4 inches
Width: 15 inches
Height: 3 inches
Material: Steel

Fabrication mount for a mendeola 2d transmission. Front mount.
Material: Steel

Fabrication mount for a mendeola 2d transmission. Front mount.
Material: Steel

Fabrication mount for a mendeola 2d transmission. Rear mount.
Welding Required
Hold Spacing:
Upper Inner: 10-1/8 inches
Upper Outer: 9-7/8 inches
Outer Upper: 14 inches
Outer Lower: 14 inches
Width: 15-1/8 inches
Material: Steel

Replace a broken front trans mount with this oem weld in mount

This is a custom front transmission mount for a vw transmission.
It is the same mount we use on all of our custom torsion housings. This mount is meant to be welded onto the torsion housing to replace a broken stock unit.
Fits a 2-1/4 OD tube. Will fit a stock torsion tube with a little fitment

Engine Mount For 68-71 Type 2 Bus. Sold Each
Bus Type 2: 68-71.