SWAY BARS for Type 3 Squareback 1963

Sway bar for lowered front beam. Improve handling and control body sway. Includes red urethane bushings. Fits king pin front ends up to 1965 that have been lowered. Use with your orginal clamps or use stainless steel clamp kit part number 00-9692-0 sold separately

Improve handling and control body sway Includes red urethane bushings. Fits king pin front ends up to 1965. Use with your orginal clamps or use stainless steel clamp kit part number 00-9692-0 sold separately

Improve handling and control body sway under hard cornering. Includes red urethane bushings. Fits 1966 and later ball joint front ends that have been lowered. Use with your orginal clamps or use stainless steel clamp kit part number 00-9692-0 sold separately

Type 1 Sway Bar, 3/4 Front Ball Joint,66 & Later. Improve handling and control body sway while preventing wheel hop under hard cornering. The EMPI high performance sway bar is zinc plated steel and includes red urethane bushings. The sway bar installs with the original clamps or Stainless Steel clamps can be purchased separately. 00-9692-0 sold separately

EMPI s Type 1 front sway bar for 1971-1973 Super Beetle models is made of 3/4 zinc-plated steel and comes with red urethane bushings. Customers that want to install this sway bar will have to use the original mounts. The sway bar is attached to the car in four places. The two stock clamps and the new bushings that come with this kit secure the middle section of the bar to the chassis. The two ends of the sway bar fit into the control arm with press-in bushings that can be found in EMPI s control arm bushing kit (P/N 16-5107). Installing a front sway bar improves handling by controlling body sway and prevents wheel hop under hard cornering. Fits VW super beetle front ends up to 1973. Use with your orginal clamps or use stainless steel clamp kit part number 00-9692-0 sold separately

Inprove handling and control body sway Includes red urethane bushings.
Fits VW super beetle front ends 1974 & Later.
Use with your orginal clamps or use stainless steel clamp kit part number 00-9692-0 sold separately.

Type 2 Sway Bar, 7/8 Front 55-67. Improve handling and control body sway while preventing wheel hop under hard cornering. The EMPI high performance sway bar is zinc plated steel Includes red urethane bushings Fits Type 2 Bus 55-67 Use with your orginal clamps.

Type 2 Sway Bar, 7/8 Front 68-79. Improve handling and control body sway while preventing wheel hop under hard cornering. The EMPI high performance sway bar is zinc plated steel and includes red urethane bushings. The sway bar installs with the original clamps. Use with your orginal clamps

EMPI s Type 1 sway bar for 1969 and later models (with I.R.S.) comes complete with all the bushings, brackets and hardware needed for installation. The bar is made of 3/4 zinc-plated steel. This sway bar kit is not a replacement for an original part, but can be mounted without any modification to the car. The steel clamps hold the bushings against the torsion tube and the brackets bolt between the spring plate and the trailing arm. Installing a rear sway bar improves handling by controlling body sway and prevents wheel hop under hard cornering.

EMPI s deluxe sway bar mounting kit for the stock bar is designed for use with a 1/2 diameter sway bar. The kit fits all Standard VW Beetle through 1979 and Karmann Ghia models through 1974. The complete deluxe kit comes with 4 red urethane bushings and stainless steel t-bolt style clamps to secure the sway bar to the trailing arms. This kit fits link pin and ball joint front ends.

EMPI s Type 2 sway bar for 1969 and later models (with I.R.S.) comes complete with all the bushings, brackets and hardware needed for installation. The bar is made of 7/8 zinc-plated steel. This sway bar kit is not a replacement for an original part, but can be mounted without any modification to the car. The steel clamps hold the bushings against the torsion tube and the brackets bolt between the spring plate and the trailing arm. Installing a rear sway bar improves handling by controlling body sway and prevents wheel hop under hard cornering.

Urethane bushings with stainless steel t-bolt type clamps. Fits both ball joint and king pin front suspensions. This one fits a 3/4 inches aftermarket bar

Sway bar mount kit is a stock replacement for the factory bushings and clamps used to mount the sway bar to your ball joint front end (for both sides) type 1 66-77, ghia 66-74

EMPI's Stainless Steel T-Bolt Sway Bar Clamps are the simple way to mount your stock or 3/4 inch sway bar. The stainless steel sway bar clamps unbolt and wrap around the sway bar bushings and sway bar and with everything in place, the T-Bolts can be tightened up. The bolt on clamps are far easier to install than the original compression clamps and fit all Type 1 models (1954 through 1977 Standard Beetles, 1956 through 1974 Karmann Ghias and 1973 through 1974 Things).

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.
For super beetle 71-73
15-piece kit
Quantity: 15 Piece Kit

BUGPACK BRAND
Now the super beetle owner can replace his inferior front control arm rubber bushings with these high quality prothane.
Material: Prothane...

BUGPACK BRAND
Material: Prothane...

The strength and durability of urethane will out-last and out-perform standard rubber products in every application.
For super beetle 74-79 15-piece kit
Super Beetle: 74-79
Quantity: 15 Piece Kit

BUGPACK BRAND
Material: Prothane

BUGPACK BRAND
For super beetle 74-79
Material: Prothane..

BUGPACK BRAND
Fits VW King Pin and Ball Joint suspension.
This one fits a 12mm inches Bar
Front Suspension: All Type 1
Quantity: 4 Pieces

BUGPACK BRAND
This one fits a 3/4 inches Bar
Quantity: 4 Pieces

BUGPACK BRAND
Urethane bushings for front sway bar.
Fits Super Beetle suspensions. This one fits a 3/4 inches Bar
Material: Prothane
Quantity: 4 Pieces

BUGPACK BRAND
Quantity: 4 Pieces

Triangulates the shock towers and the frame horns, helping to prevent movement of the engine and transmission upon acceleration preventing wheel hop.
Adjustable rod ends allow for variations and/or preload. Features 3/4 steel tubing, black powder coating for good looks and durability.
Fits 61 and later beetle, Super Beetle and Ghia.
Does not fit with a SR17 Starter.
NOTE: Some applications may require slight trimming/modifications to the body panels for installation
Beetle Tyle 1: 61 and up
Ghia: 61 and up
Transmission: Swing & IRS

The EMPI Camber Compensator is designed to protect against over-camber on Swing Axle Bugs. Easily bolts to the bottom of the transmission and features zinc plated steel components and urethane bushings. Fits all full synchro Swing Axle Bugs

Prevents wheel hop and engine flex by supporting the rear of the engine. Fits all type 1 applications

Replacement sway bar mounting kit for Type 2 Bus 68-79
Both Sides