LINKAGE KITS for Type II Bus Bus 1961

Replacement linkage kit only for empi single hpmx / idf intake manifold 43-5208-0

Linkage kit for ida carbs as well as empi 48/51. Contains hex aluminum cross shaft, aluminum throttle bars, sealed aircraft heim joints and all the adjusters and hardware

High quality linkage kit featuring thick heavy duty mounting plates, aircraft quality heims and all necessary hardware and gaskets. Fits weber idf and empi hpmx carb kits to type 1 and type 3 engines

Complete kit with air cleaners.
High quality linkage kit featuring thick heavy duty mounting plates, aircraft quality heims and all necessary hardware and gaskets.
Includes air cleaners with aluminum top and bottom plates
Fits weber idf and empi hpmx carb kits to type 1 and type 3 engines

This fool proof hex linkage contains all of the quality hardware and features the same mounting system as the tayco units with the simplicity of alignment that only a hex linkage can offer. For Type 3 Hex Bar is 27.25 Long

This fool proof hex linkage contains all of the quality hardware and features the same mounting system as the tayco units with the simplicity of alignment that only a hex linkage can offer. For 1700 and 2000cc Type 2 Engines Hex Bar is 26 Long

This fool proof hex linkage contains all of the quality hardware and features the same mounting system as the tayco units with the simplicity of alignment that only a hex linkage can offer.
Features a 18.5 inch long hex bar
For Type 2 and 4 Engines

Featuring the same components that are included in our dual type 2 carb kits. Can be used to replace linkage for kits 43-4500 43-4520 43-4431
For Type 2 and 4 Engines

This fool proof hex linkage contains all of the quality hardware and features the same mounting system as the tayco units with the simplicity of alignment that only a hex linkage can offer.
Features a 26 inch long hex bar
For Type 1 Engines

Upgrade or replace worn dual carb linkage with this kit, includes everything neccessary for your brosol/solex carbs

This kit fits IDF and HPMX series dual carb kits.
Hex bar design with aircraft quality linkage.
Includes all the gaskets and hardware you would need to install.

Twist style dual carb linkage for your solex or brosol carbs. Features the best and strongest combination of components: Billet aluminum stand, 5/16 steel pivot bolt, steel linkage, 3/8 inches aluminum linkage rods with adjustable heim joints and stamped steel carb linkage arms

Complete kit with off-set manifolds, linkage, hi-flow gauze air filter elements, coil relocation bracket, hardwrae, gaskets, detailed illustrations for assembly. Just add carbs

Right and Left replacement heim joints for dual carb linkage.
10/32 thread
Quantity: Sold as a Pair

Replacement down linkage from the hex bar to the carb throttle bodies.
1 1-3/4 inch adjuster rod
43-5221-0
43-5222-0
43-7301-0
43-7311-0
43-7412-0
47-7301-0
47-7311-0
47-7412-0
Length: 1-3/4

Replacement down linkage from the hex bar to the carb throttle bodies. 48-51 EPC & IDA
1 3-1/2 inch adjuster rod
43-5240-0
43-5242-0
43-7328-0
43-7329-0
43-7332-0
43-7333-0
43-7341-0
43-7342-0
47-7328-0
47-7329-0
47-7330-0
47-7331-0
47-7341-0
47-7342-0
47-7429-0
Length: 3-1/2

Connects the upper and lower ball joints on a dual carb linkage kit

Replacement down linkage from the hex bar to the carb throttle bodies.
Works for HPMX and WEBER carbs
1 Left hand threaded ball joint
1 Right hand threaded ball joint
2 Jam Nuts
1 4-1/2 inch adjuster rod
Used in the following kits:
43-5223-0
43-5230-0
43-6317-0
43-6319-0
43-7317-0
43-7319-0
43-8317-0
Length: 4-1/2

Replacement down linkage from the hex bar to the carb throttle bodies.
1 6-1/2 inch adjuster rod
43-5220-0
43-7401-0
43-7411-0
47-7401-0
47-7411-0
Length: 6-1/2

Replacement heim joint extensions for dual carb linkage. These extensions allow you to easily make linkage that pull in the same direction to keep the carbs in sync.
These come with with both short and long extensions.
Quantity: Sold as a Pair

Retrofits all empi hex bar linkage to upgrade from the ball and bushing ends to needle bearing for a smooth operation.
Helps maintain carburetor and linkage adjustment and synchronization

Replacement ball socket ends.
10/32 right hand thread.
These are used on all EMPI Brosol carb kits
Quantity: Sold as a Pair

Return spring for throttle plate on carburetor. Fits all stock style VW carbs. Make sure your throttle closes all the way with this new spring. Old springs get worn out and stretched and can lead to high rpm idle and in the worst case, a stuck wide open throttle.
Type 1 65-74
Ghia 65-74
Type 2 65-71
Quantity: Sold Each

Replace your worn out bushings at the end of your dual carb linkage with a new set from EMPI. Fits all EMPI Dual carb kits with ball ends
Carb Type: Duals
Quantity: Sold as a Pair.