RACK & PINIONS for Type II Bus Bus 1963

Thin line....5/16 Heim

11 inches rack and pinion. Nice setup for small sand rails and dragster. Aluminum body. Measures 11 inches eye to eye and 1-1/4 inches on the bolt spacing
1-1/2 Turn Lock to Lock

Thin line, 5/8 - 36 spline shaft.
Made from high quality aluminum.
Length: 11 inches
Mounting Holes: 1.30 OC 3/8 inches
Heim Hole: 3/8 inche.

Heavy duty rack & pinion beam mount, international tie rod ends. Features built in stops. Cast body and billet gears. Polished for a custom look. Mounting holes measure 6 inches spacing, tie rod holes are 2-1/2 inches eye to eye and 12 inches overall. 1:1 ratio with roughly 3 inches of travel

Monster Heavy Duty wide spread rack and pinion. Center load style. Billet Aluminum construction. 3/4-48 spline

Center load rack and pinion. Polished billet aluminum body. Tie rods pivot from the center. Use this rack and long travel sand rails were suspension travel is great. Mounting holes measure 6 inches apart. 2-1/2 inches tall and 2-1/4 inches wide. 10-5/8 inches overall length. 5/8 36 spline shaft. Uses 1/2 inches fine thread for tie rod connection

Billet Aluminum. Really heavy duty rack. Tie rods pivot from out at the ends. Giant steel clevis to mount tie rods to. Billet body that has been polished for a nice custom look.
Travel: 2 inches 4 Inches Lock to Lock
Bolt Pattern: 6 inches x 1 inches

Replacement clevis. Fits our end load rack & pinions
5/8-18 Right Hand Thread
1/2 Inch Hole
3/4 Inch Slot

Same as our cast unit only made from billet aluminum. Great premium unit to get the most from your suspension.

3/4-48 spline

This handy chrome rack mount is a simple way to convert your old steering system to rack and pinion. Simply clamp this unit in the center of your beam and the rack bolts straight to it. Works with 14 inches rack. THIS MOUNT IS FOR KING PIN FRONT ENDS, WILL NOT FIT ON A BALLJOINT BEAM.

This weld on plate allows you to install the center load rack and pinion units to your car. This is a universal plate and can be cut by the final user to fit their application. Made of thick 1/4 inches plate steel

Weld on rack mount for heavy duty rack and pinion. Requires welding. Predrilled for ease of installation. Mounts the rack to the AC401010 axle beam for proper geometery.
Bolt pattern: 6 inches x 1 inches
Bolt hole diameter: .414 inches
Height: 3 1/4 inches
Thickness: 1/4 inches

Weld on rack mount for heavy duty rack and pinion. Requires welding. Predrilled for ease of installation.
Length (Top): 8 1/2 inches
Length (Bottom): 10 1/4 inches
Height: 2 1/2 inches

This weld on bracket allows you to install different rack and pinion units to your car. This one is for wider warrior style beams

Allows for easy setup of our 14 inches rack & pinion. Simply weld on in the desired location and bolt the rack up..
Thickness: 1/8 inches

5/8 inches 36 spline coupler to be used to hook a rack and pinion to a steel shaft. Requires welding. 2 inches long.
Length: 2 inches

3/4 inches 36 spline coupler to be used to hook a rack and pinion to a steel shaft. Requires welding.
Quantity: Sold Each

Charlynn key way for power steering assist coupler to be used to hook a rack and pinion to a steel shaft. Requires welding. 2 inches long.
To be used specificaly with a Charlynn Power Steering Pump.
Quantity: Sold Each

Splined 1/2 inches way through with a locking screw. Fits 3/4 inches 48 spline racks. Welds to the end of your steering shaft. 2 inches long.
Length: 2 inches

Replacement boot for our 14 inches rack and pinion. Sold Each
Replacement For: AC425155 & AC425155H
Sold: Each