ENGINE HINGES & SPRINGS for Type II Bus Bus 1977
Items:
1–58 of 58
Sort by:
Recommended
-
Replaces stock brackets with a new chrome pair. Show quality finish for a custom look
These are compatible with 1954-1977 Beetles and 1971-1979 Super Beetles. -
In 2004 famed PRA racers Buster John and Joe Maestas designed this custom one off Billet Deck Lid Stand-Off for their Ren Kafer cars. These products became so popular that companies started reproducing them. These Stand-Offs allow you to prop your deck lid approximately 2 1/2 so the larger velocity stacks running with dual carbs fit and still lock your deck lid. Made of 6061 billet aluminum. JayCee Billet Stand-Offs come anodized and laser engraved to ensure that your getting an original made in the USA JayCee product and not some foreign knock-off . Available in Red, Blue, Black, or Polished finish.
-
In 2004 famed PRA racers Buster John and Joe Maestas designed this custom one off Billet Deck Lid Stand-Off for their Ren Kafer cars. These products became so popular that companies started reproducing them. These Stand-Offs allow you to prop your deck lid approximately 2 1/2 so the larger velocity stacks running with dual carbs fit and still lock your deck lid. Made of 6061 billet aluminum. JayCee Billet Stand-Offs come anodized and laser engraved to ensure that your getting an original made in the USA JayCee product and not some foreign knock-off . Available in Red, Blue, Black, or Polished finish.
-
Billet deck lid stand-off. Designed to space rear deck lid cover from body allowing heat to escape from engine compartment allowing engine to run cooler. Cast aluminum brackets are installed between rear deck lid and stock hinge. Fits all type 1. Sold Each
-
Designed to space rear deck lid cover from body allowing heat to escape from engine compartment allowing engine to run cooler. Cast aluminum brackets are installed between rear deck lid and stock hinge
-
Replaces the stock deck lid spring with a new chrome one. Replace your worn out spring with this show quality replacement
It fits the 1958-1977 Beetle and 1971-1979 Super Beetle. -
Replaces stock hinges for that show car look.
All type 1 except super beetle.
Sold as a pair -
By removing the existing deck lid hinge pins and using these quick release clip/pins you can easily remove your deck lid for your engine tuning any time you want. Great for sedans with dual carbs were you can never get your arm into the right spot or for those of you who happened to always hit their head on the deck lid! sold as a pair
-
Sold as Pair. If your tired of that same inches squawk inches when you open the front hood, we have the answer.
These up to date struts are an affordable and functional update to any street or show car.
NOTE: These do NOT fit Super Beetle
Type 1 Beetle: All Years
Quantity: 2 Pieces -
The same quick removal pins and clips included with Allstar fts hood pin kits. Hair pin clip has a rotated loop for easy grasp and the flip over clips have a loop with an over center locking feature that keeps pin in place. Package of 2.
-
Steel lanyards feature 1/16 In diameter cable with 3/4 In loops on each end for light duty applications such as hood pins or retention of similar type fasteners to prevent loss.
-
Our most popular size flip-over clip commonly used with hood pins is now available with an added lanyard which fastens to body panel for easy installation and prevention of lost clips. Sold each.
-
The same quick removal pins and clips included with Allstar fts hood pin kits. Hair pin clip has a rotated loop for easy grasp and the flip over clips have a loop with an over center locking feature that keeps pin in place. Package of 2.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Supports thread onto hood pins (before installation) and are a good alternative to sections of rubber hose commonly used to support hoods and deck lids. Once supports are in place, a set screw prevents movement. Supports work with Allstar Performance aluminum hood pins and other fully threaded hood pins. Package of 2.
-
The same quick removal pins and clips included with Allstar fts hood pin kits. Hair pin clip has a rotated loop for easy grasp and the flip over clips have a loop with an over center locking feature that keeps pin in place. Package of 2.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Kits include two each: 4 In x 1/2 In dia. aluminum pins, aluminum scuff plates, flip over style, 1/4 In dia. steel clips, and four nuts. Clip flips over pin and over-center action locks clip in place.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Use steel hinge kits on hoods and deck lids for quick, one person inspection of engine compartment or trunk area. Universal kits include two complete hinges.
-
Kits include two each: 4 In x 1/2 In dia. aluminum pins, aluminum scuff plates, flip over style, 1/4 In dia. steel clips, and four nuts. Clip flips over pin and over-center action locks clip in place.
-
Scuff plates are used to protect painted finishes from repeated hood pin clip use. Plates are drilled for mounting screws or 1/8 In diameter rivets. Package of 4.
-
Mounts ease hood pin installation. Choose from boss or tab style.
-
Scuff plates are used to protect painted finishes from repeated hood pin clip use. Plates are drilled for mounting screws or 1/8 In diameter rivets. Package of 4.
-
Use steel hinge kits on hoods and deck lids for quick, one person inspection of engine compartment or trunk area. Universal kits include two complete hinges.
-
Aluminum adapters convert existing chassis mounts over to hood pin mounts.
-
Scuff plates are used to protect painted finishes from repeated hood pin clip use. Plates are drilled for mounting screws or 1/8 In diameter rivets. Package of 4.
-
Kits include two aluminum 3-1/2 In x 3/8 In dia. pins, two aluminum scuff plates, two flip over style 3/16 In dia. steel clips, and four nuts. Clip flips over stud and locks into place. Over-center action keeps clip in place.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Aluminum extensions fit into existing chassis mounts. 1/2 In-20 male to 1/2 In-20 female.
-
Our most popular size flip-over clip commonly used with hood pins is now available with an added lanyard which fastens to body panel for easy installation and prevention of lost clips. Sold each.
-
Nylon lanyards feature a pre-molded end with a 3/16 In hole on one end and a snap together open loop on the other end to quickly and easily secure a variety of components. Once snapped together, loop is permanently locked. 10 In long, package of four.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Aluminum hood prop is a must for supporting lightweight aluminum and fiberglass hinged hoods or trunk lids commonly found on asphalt template body cars. Prop mounting hole distance is 17-1/4 In when open. Sold each.
-
Kits include two each: 4 In long x 1/2 In dia. chrome steel pins, chrome steel scuff plates, clips, and four nuts. Available with flip-over or hairpin-style clips.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Aluminum extensions fit into existing chassis mounts. 1/2 In-20 male to 1/2 In-20 female.
-
Kits include two aluminum 3-1/2 In x 3/8 In dia. pins, two aluminum scuff plates, two flip over style 3/16 In dia. steel clips, and four nuts. Clip flips over stud and locks into place. Over-center action keeps clip in place.
-
Kits include two aluminum 3-1/2 In x 3/8 In dia. pins, two aluminum scuff plates, two flip over style 3/16 In dia. steel clips, and four nuts. Clip flips over stud and locks into place. Over-center action keeps clip in place.
-
Kits include two 2-3/4 In long gun-drilled aluminum pins, two clips, two lightweight aluminum plates and four steel jam nuts.
-
Kits include two 2-3/4 In long gun-drilled aluminum pins, two clips, two lightweight aluminum plates and four steel jam nuts.
-
Universal bracket with 1/4 In mounting holes can be bolted on or welded in place. Bracket accepts 1/2 In hood pins to secure hood and deck lids along with many other uses. Constructed of.100 In steel, bracket has a built-in reinforcing gusset for added strength.
-
Mounts ease hood pin installation. Choose from boss or tab style.
-
Steel lanyards feature 1/16 In diameter cable with 3/4 In loops on each end for light duty applications such as hood pins or retention of similar type fasteners to prevent loss.
-
Supports thread onto hood pins (before installation) and are a good alternative to sections of rubber hose commonly used to support hoods and deck lids. Once supports are in place, a set screw prevents movement. Supports work with Allstar Performance aluminum hood pins and other fully threaded hood pins. Package of 2.
-
Sturdy plastic scuff plates have a raised center for quick easy removal of hood pin clips. Plates have a 1/2 In center hole and four recessed rivet holes for simplified installation.
-
Scuff plates are used to protect painted finishes from repeated hood pin clip use. Plates are drilled for mounting screws or 1/8 In diameter rivets. Package of 4.
-
Kits include two each: 4 In x 1/2 In dia. aluminum pins, aluminum scuff plates, flip over style, 1/4 In dia. steel clips, and four nuts. Clip flips over pin and over-center action locks clip in place.
-
Scuff plates are used to protect painted finishes from repeated hood pin clip use. Plates are drilled for mounting screws or 1/8 In diameter rivets. Package of 4.
-
Kits include two each: 4 In x 1/2 In dia. aluminum pins, aluminum scuff plates, flip over style, 1/4 In dia. steel clips, and four nuts. Clip flips over pin and over-center action locks clip in place.
-
Hood pin kit include two each: 4 In x 1/2 In dia. aluminum pins, aluminum scuff plates, flip over style, 1/4 In dia. steel clips, and four nuts. Clip flips over pin and over-center action locks clip in place.
-
Kits include two aluminum 3-1/2 In x 3/8 In dia. pins, two aluminum scuff plates, two flip over style 3/16 In dia. steel clips, and four nuts. Clip flips over stud and locks into place. Over-center action keeps clip in place.
-
Aluminum adapters convert existing chassis mounts over to hood pin mounts.