BRAKE LINES, STAINLESS BRAIDED for Type II Bus Double Cab 1958

Brake line kits are pre-assembled and individually pressure tested to 4500 psi. Kits are made from teflon hose with stainless steel outer braid and include all adapters
Quantity: 4 Pieces

Brake line kits are pre-assembled and individually pressure tested to 4500 psi. Kits are made from teflon hose with stainless steel outer braid and include all adapters
Quantity: 4 Pieces

Brake line kits are pre-assembled and individually pressure tested to 4500 psi. Kits are made from teflon hose with stainless steel outer braid and include all adapters
Beetle Type 1: 68-Up
Quantity: 4 Pieces

Brake line kits are pre-assembled and individually pressure tested to 4500 psi. Kits are made from teflon hose with stainless steel outer braid and include all adapters
Quantity: 4 Pieces

Brake line kits are pre-assembled and individually pressure tested to 4500 psi. Kits are made from teflon hose with stainless steel outer braid and include all adapters
Beetle Type 1: 58-65
Material: Braided Stainless
Quantity: 4 Pieces

Braided stainless steel brake line. Stock replacement for front long travel. Sold individually. Extra long for extended travel suspensions
Material: Braided Stainless

DOT Approved with Kevlar Liner
Braided stainless steel brake line. Stock replacement for front to 1964.
Material: Braided Stainless

Braided stainless steel brake line. Stock replacement for front to 1964.
Sold individually
Location: Front Beetle
Length: 18.5 inches
Material: Braided Stainless

Braided stainless steel brake line. Stock replacement for front to 1965-66.
Female-Male Ends
Location: Front 65-66
Length: 17.5/8 inches
Material: Braided Stainless

DOT Approved with Kevlar Liner
Braided stainless steel brake line. Stock replacement for front to 1965-66.
Material: Braided Stainless

DOT Approved with Kevlar Liner
Braided stainless steel brake line. Stock replacement for front to 67 on.
Location: Front 67-79
Length: 15 inches
Material: Braided Stainless

Braided stainless steel brake line. Stock replacement for front super beetle. Sold individually.
Female-Female Ends
Location: Front Super Beetle
Length: 13-13/16 inches
Material: Braided Stainless

DOT Approved with Kevlar Liner
Braided stainless steel brake line. Stock replacement for rear swing axles. Sold individually.
Female 10mm and Female 10mm
Length: 10-9/16 inches
Quantity: Sold Each

Kit is designed to eliminate hanging brake lines near the rear calipers. Rear Brake Line Kits utilize a single line drop located near the left side of the center section. From the drop, the lines tee and run over the top back side of the center section, then across the backside of axle tubes to the calipers. Braided lines are #3 with -4AN ends.

Kits include braided lines to reach from the front calipers to inside the foot box. Braided lines are #3 size with -4AN ends. The #3 line size offers a stiffer pedal feel while utilizing the more popular -4AN ends.

Kit allows braided lines to be run throughout a dirt race car. Includes all lines needed to reach from the calipers to inside the foot box. Due to brand preference and location of pedals, master cylinders and brake shut off, the specific fittings and lines to complete plumbing inside the foot box area will need to be purchased separately.

Kit allows braided lines to be run throughout a dirt race car. Includes all lines needed to reach from the calipers to inside the foot box. Due to brand preference and location of pedals, master cylinders and brake shut off, the specific fittings and lines to complete plumbing inside the foot box area will need to be purchased separately.

Kit allows braided lines to be run throughout a dirt race car. Includes all lines needed to reach from the calipers to inside the foot box. Due to brand preference and location of pedals, master cylinders and brake shut off, the specific fittings and lines to complete plumbing inside the foot box area will need to be purchased separately.

Kit is designed to eliminate hanging brake lines near the rear calipers. Rear Brake Line Kits utilize a single line drop located near the left side of the center section. From the drop, the lines tee and run over the top back side of the center section, then across the backside of axle tubes to the calipers. Braided lines are #3 with -4AN ends.

Kit is designed to eliminate hanging brake lines near the rear calipers. Rear Brake Line Kits utilize a single line drop located near the left side of the center section. From the drop, the lines tee and run over the top back side of the center section, then across the backside of axle tubes to the calipers. Braided lines are #3 with -4AN ends.

Kits include two 16 In long #3 stainless steel braided lines with banjo fittings attached, banjo bolts, crush washers, frame adapter fittings, frame tabs and holding clips.

Kits include everything necessary to complete the connection between a 3/16 In steel brake line and the brake caliper including two 15 In steel braided hoses. Designed to fit calipers with 10mm x 1.50 threads (ALL42083/ALL42084) or 7/16 In x -20 threads (ALL42081/ALL42082).

Kits include braided lines to reach from the front calipers to inside the foot box. Braided lines are #3 size with -4AN ends. The #3 line size offers a stiffer pedal feel while utilizing the more popular -4AN ends.

Kits include braided lines to reach from the front calipers to inside the foot box. Braided lines are #3 size with -4AN ends. The #3 line size offers a stiffer pedal feel while utilizing the more popular -4AN ends.

DOT Approved with Kevlar Liner
Braided stainless steel brake line. Stock replacement for rear irs. Sold individually
Brake Line Ends: Metric 10mm