STEERING for Vanagon Vanagon 1989

These quality die stamped mild steel flanges eliminate the need for cutting and filing. 1 per pack. Hole diameter 1/4 inches 1/8 inches thick tube dia. 7/8 inches steering applications.
Hole Diameter: 3 x 1/4 inches
Hole Diameter: 1 x 7/8 inches

Splined shaft to connect steering shaft to coupler or u-joints. 2 inches long, 5/8-36 spline. Requires welding.
Length: 2 inches

3/4 in .120 wall raw steering shaft.
3 bolt flange for fitting almost any steering wheel. This flange will accept most 3 bolt wheels. If you have anothing other than a 3 bolt flange, you will just need to pick out one of our adapters
Length: 59 inches
Diameter: 3/4 inches
Finish: Raw

Steering shaft. 7/8 inches diameter.
Diameter: 7/8 inches
Finish: Raw

Splined shaft to connect steering shaft to coupler or u-joints. 12 inches long, 5/8-36 spline. Requires welding.
Quantity: Sold Each

Quantity: Sold Each
Quantity: Sold Each

3/4 in .120 wall steering shaft.
Chrome finish. 3 bolt flange for fitting almost any steering wheel. This flange will accept most 3 bolt wheels. If you have anothing other than a 3 bolt flange, you will just need to pick out one of our adapters
Finish: Chrome

Splined shaft to connect steering shaft to coupler or u-joints. 6 inches long, 5/8 inches -36 spline. Requires welding.
Quantity: Sold Each

Chrome steering shaft. 7/8 inches diameter .120 wall.
Finish: Chrome

Splined shaft to connect steering shaft to coupler or u-joints. 3-3/4 inches long, 3/4 inches -36 spline. Splined on both ends.
Length: 3 3/4 inches
Quantity: Sold Each

Splined shaft to connect steering shaft to coupler or u-joints. 18 inches long, 3/4 inches -36 spline. Requires welding.
Quantity: Sold Each

Splined shaft to connect steering shaft to coupler or u-joints. 12 inches long, 3/4 inches -48 spline. Requires welding.
Quantity: Sold Each

Splined shaft to connect steering shaft to coupler or u-joints. 18 inches long, 3/4 inches -48 spline. Requires welding.
Quantity: Sold Each

For rack & pinion units, 36 spline.
Length: 1 5/8 inches

Weld on rack mount for heavy duty rack and pinion. Requires welding. Predrilled for ease of installation. Mounts the rack to the AC401010 axle beam for proper geometery.
Bolt pattern: 6 inches x 1 inches
Bolt hole diameter: .414 inches
Height: 3 1/4 inches
Thickness: 1/4 inches

Weld on rack mount for heavy duty rack and pinion. Requires welding. Predrilled for ease of installation.
Length (Top): 8 1/2 inches
Length (Bottom): 10 1/4 inches
Height: 2 1/2 inches

This weld on bracket allows you to install different rack and pinion units to your car. This one is for wider warrior style beams

5/8 inches 36 spline coupler to be used to hook a rack and pinion to a steel shaft. Requires welding. 2 inches long.
Length: 2 inches

3/4 inches 36 spline coupler to be used to hook a rack and pinion to a steel shaft. Requires welding.
Quantity: Sold Each

Allows for easy setup of our 14 inches rack & pinion. Simply weld on in the desired location and bolt the rack up..
Thickness: 1/8 inches

Charlynn key way for power steering assist coupler to be used to hook a rack and pinion to a steel shaft. Requires welding. 2 inches long.
To be used specificaly with a Charlynn Power Steering Pump.
Quantity: Sold Each

Splined 1/2 inches way through with a locking screw. Fits 3/4 inches 48 spline racks. Welds to the end of your steering shaft. 2 inches long.
Length: 2 inches

This weld on plate allows you to install the center load rack and pinion units to your car. This is a universal plate and can be cut by the final user to fit their application. Made of thick 1/4 inches plate steel